Blog by affiliatereview-generator.com

Archive for the ‘CNC’ Category

Would you like to find out what those-in-the-know have to say about CNC? The information in the article below comes straight from well-informed experts with special knowledge about CNC.

What is the definition of cycle time?

Cycle time is defined to be the time that happens from the time a task or series of tasks is initiated to the time a task is completed. Example, the cycle time is the time a shipping order is printed to the time it is loaded on the truck and the system is updated. An alternate definition would be is the time it takes to load, run, and unload on workpiece.

Cycle time of a machine can be simply measured by timing how long it takes from pressing the button to start the cycle for the first workpiece to the pressing the next button for the next workpiece.

Production quantities in an industry dictate that the more workpieces you run, the more important it is to achieve the goal of lowering the cycle time.

Everything and anything that happens in a Computer Numerical Control (CNC) machining equipment can be divided into four categories:

1.) On-line, productive tasks:

These are the actual machining operations that occur during a CNC cycle. These are the milling, drilling, tapping, reaming, and any other machining operation that in some way furthers the completion of the workpiece. To minimize the cycle time in these areas, there are two ways in which this can be achieved. One would be through careful process planning.

The process engineer must select an appropriate machine tool, cutting tools, fixturing, and machining order in a way that it matches the number of workpieces to be machined that will be based on the production quantity. The cycle time will be a reflection of the processes being used to machine workpieces.

If you find yourself confused by what you’ve read to this point, don’t despair. Everything should be crystal clear by the time you finish.

If in the many times that your company’s processes have already been developed and implemented before you begin your cycle time reduction program, then your second alternative is to optimize cutting operations for this would involve properly selecting cutting tool materials, feeds, and speeds to machine workpieces as efficiently as possible with the current process.

2.) On-line, non-productive tasks:

These are tasks that occur during the machining cycle that do not actually further the completion of the workpiece. The first thing Computer Numerical Control people often target for improvement is wasted program execution time. These are the things like rapid movements, tool changes, M-code execution and spindle acceleration/deceleration. Reducing program execution time in this area is usually easy.

It often takes nothing more than carefully monitoring the production run for a few workpieces to find those times when the program can be modified to eliminate noticeable pauses during the cycle. Although keep in mind that the worker for these machines must not overlook other processes for they may be so concerned with minimizing program execution that they overlook other operations, resulting in severe wastes of cycle time.

3.) Off-line, non-productive tasks:

These are the tasks performed in the machining cycle that do nothing to further the completion of the workpiece. Since these types of tasks are done while the machine is producing workpieces, they do not actually add to the cycle time. It is possible to free the operator of the machines of performing off-line productive tasks if they have little, or nothing to do during lengthy machine cycles.

4.) Off-line, productive tasks:

These are the tasks done away by the CNC machine, while the machine is producing workpieces, which would further the completion of the workpiece. This is extremely helpful during lengthy CNC cycles, tasks in this category can reduce the time it takes to complete the production run dramatically, which would effectively reduce cycle time.

About the Author
By Anders Eriksson, who just launched this great product..
- Do you want to make Your PDF files viral? Use This Secret Viral PDF Rebrander: Viral PDF

So what is CNC really all about? The following report includes some fascinating information about CNC–info you can use, not just the old stuff they used to tell you.

When a program is completed and sent to the Computer Numerical Control Machine, the programming process is over. All calculations were made and the algorithm fully written. But the question is the programmer’s job really finished? When is the programmer’s responsibility really over? And how can we evaluate the type of program that the Computer Numerical Control Machine programmer did?

The fairest and reasonable answer to those questions would basically when a part has been machined under the most optimized working conditions. Therefore the Programmer’s responsibility does not end after he or she finishes the program. We could say that the program at this stage is still very much in the development process, because most of the programming considerations were based on certain assumptions and there are a lot of external factors that may affect the outcome of the product.

Every Computer Numerical Control programmer should have an effort to be in the touch with the actual production. In the field of software development, Constant communication with your colleagues as well as actual machine operators of the CNC will help you to improve your own program. Because most of the time the CNC machine operators are a good source of constructive ideas, improvements and suggestions.

A good CNC programmer should talk, ask questions to them and most importantly listen to what they have to say. Programmers who never put their foot in the actual machining process and think they are always right are all on the wrong track. Exchanging ideas with CNC machine operators, asking questions and seeking answers is the only way to be fully aware of what is going on in the machine.

Whenever you start a Computer Numerical Control Program the first time it is important to check its Program Integrity. A new and unproved program is a potential source of problems. During Manual Programming in CNC, mistakes are more common than when the program is made in a CAM program.

So far, we’ve uncovered some interesting facts about CNC. You may decide that the following information is even more interesting.

A good way to look at a new program is through the machine operator’s perspective. Experienced Machine Operators take a direct approach when running a program for the first time. That means that they wont take any chances of mistakes with the actual running of a program therefore a good programmer must take note of any comments that the Machine operator will say about the program.

What does an experienced Machine Operator look for in a new part of a program? Most of the Machine operators would say that the first and most important thing to be checked on a Computer Numerical Control Program is its consistency. Therefore a machine operator looks at how a CNC programmer does its own programming, is the way you create your own algorithms the same as the other ones. Machine Operators take note with this kind of Information.

Upgrading your CNC Program

Whenever you upgrade your own program, it means that you are strengthening or enriching it, therefore making it better than it was before. Upgrading would be based on this standard, It is to decrease the production cost without compromising the quality of the part being manufactured or the safety of the Computer Numerical Control Machine Operator.

One of the Most Common forms of Program Optimization is doing some minor changes to the spindle as well as the feed rates of the machines. This process is called cycle time optimization, slightly increasing the spindle speed and feed rates of these machines will decrease the time it takes to finish the part.

And when we compare it to mass production, saving one second for each part in a batch of 3600 pieces would mean an hour saved. Efficiency in the rate of production is a very important aspect in Mass Production.

About the Author
By Anders Eriksson, who just launched this great product..
- Do you want to make Your PDF files viral? Use This Secret Viral PDF Rebrander: Viral PDF

Are you good with computers and looking for a job? Well then, consider being a CNC machine operator. It’s usually easy, full-time and the name isn’t intimidating, right?

If you think that being a Computer Numerical Control (CNC) machine operator may be a bit out of your reach, think again. You don’t have to be a math wizard or a programming genius to get that position. But don’t jump in just yet! There are a few things that you have to know (and consider! ) before applying for the job.

The first thing that you have to understand is the abbreviation CNC. According to an online encyclopedia, CNC stands for Computer Numerical Control, and refers specifically to a computer ?controller? that reads G-code instructions and drives a machine tool, a powered mechanical device typically used to fabricate components by the selective removal of material. CNC does numerically directed interpolation of a cutting tool in the work envelope of a machine. The operating parameters of the CNC can be altered via a software load program.

THE PROS

The good thing about being in this job is that the workload is actually light. Operators even complain of boredom because the cycles of CNC machines are all automated. All they have to do is initiate the sequence, sit back, watch for malfunctions, adjust the performance of each machine, and turn them off. If your boss is kind enough to let you use an MP3 player while working, then you sure are lucky.

Another good thing about this job is that job openings for this position will always rise. Technology is moving forward. CNC machining will certainly lead the demand because in CNC, a group of machines can be controlled at the same time. That is exactly what big-time companies want, right? To reduced manual overseeing and just leave it to the machines.

If you find yourself confused by what you’ve read to this point, don’t despair. Everything should be crystal clear by the time you finish.

Advantage in this job arena is easy too. Statistics show that you will need only a high school diploma and (more importantly) an experience in CNC operations to gain an edge.

THE CONS

The thing is, when you’re in this line of work, it is repetitive. One gets bored after doing the same mechanical thing over and over again. As time withers, you will reach a point where you will breathlessly wait for the next paycheck and not actually care about the job. It’s emotionally exhausting. Furthermore, programming and operating these machines can be tedious. So, add that up to boredom and you get disproductivity.

Another thing that you should think about is the work environment. You’re going to be working in a factory. And factories are located away from town. If you’re not comfortable with being away from the hustle and bustle of the city, this might not be for you.

It can get pretty dangerous. Reports show that although most CNC operators work in a well-lit and smoothly ventilated environment, the high-power machinery poses dangers for them in the form of flying particles of metal and plastic. Also, though most modern machines produce less noise, ear plugs are still recommended by experts.

Lastly, this may not sound like a biggie, but most CNC operators are on their feet all day. They can only sit when the programs are being loaded into the computer. It’s pretty comforting that they receive salaries waaaay bigger than those salesladies.

The day will come when you can use something you read about here to have a beneficial impact. Then you’ll be glad you took the time to learn more about CNC.

About the Author
By Anders Eriksson, who just launched this great product..
- Do you want to make Your PDF files viral? Use This Secret Viral PDF Rebrander: Viral PDF

The following paragraphs summarize the work of CNC experts who are completely familiar with all the aspects of CNC. Heed their advice to avoid any CNC surprises.

Manufacturing anything that requires exact measurements requires cutting edge precision and nimbleness from the worker. Most of the time manufacturing these kinds of products requires weeks or months to finish therefore slowing down productivity as well as consistency of the manufacturers.

Computer Numerical Control or more commonly called as CNC’s are the new trend in machine shop manufacturing and practice. Any manufacturing environment owns one or is basically acquainted to this kind of device because of its capability to increase productivity as well as consistency on the products being produced.

Benchmarked from Numerical Control (NC) during the late 50′s, Computer Numerical Control incorporate the functionality of a Programmable Logic Controller (PLC), meaning you could program it to execute different functions depending on the type of manufacturing that the industry needs.

Given this kind of quality what does the Computer Numerical Control do in the practical application concept? CNC can do a variety of things depending on how the machine operator would program the system. The more acquainted the machine operator is to the CNC machine the more complex applications as well as programming can be made. Practical applications of CNC range from drilling, lathes, multi-axis spindles, milling machines, laser cutting machines, and wire electrical discharge machines.

Let’s discuss some of these common applications further. In Metal fabrication, Computer Numerical controlled Lathe’s are used to fabricate metal sheet by shearing, flame or plasma cutting, punching, laser cutting, forming and welding. Most CNC Lathe’s are used for designing modern carbide tooling. The design could be created with the Computer Aided Manufacturing (CAM) process, and when done, the CNC could start creating the product automatically with little supervision from the machine operator.

Truthfully, the only difference between you and CNC experts is time. If you’ll invest a little more time in reading, you’ll be that much nearer to expert status when it comes to CNC.

Electrical discharge machining (EDM) is the process of removing metal with the use of electrical sparks to take away the metal. These Electrical Discharge Machine has two types, the vertical EDM and wire EDM. Vertical EDM uses an electrode that is the shape of the cavity to be machined into a work piece. Wire EDM is used to create punch and die combinations in the fabrication industry. Computer Numerical Control EDM’s are not usually known because it is mostly incorporated to other CNC process.

Drilling is the most common machine process. Computer Numerical Controlled Drilling is used to create precise right circular cylinders over a certain material, the CNC could be programmed to create holes on different standards, most of the time this is the gaps between these holes. Drilling is commonly used in wood working manufacturing process in which other process is also involved such as milling, turning and grinding.

Several tools for creating holes with CNC’s involve varied hole sizes as well as drill press for creating different depths on its holes. CNC drills are equipped depending on the type of hole that the machine operator is drilling.

Applications stated above are just a few examples on what the Computer Numerical Control could execute. Depending on how you want it to perform, more complex designs can be made and a lot of things can be made in a shorter period of time, therefore the key concept for the proper use of CNC’s is that the machine operator must know what he or she wants to do.

This makes the CNC an indispensable tool for the Manufacturing Industry nowadays.

About the Author
By Anders Eriksson, who just launched this great product..
- Do you want to make Your PDF files viral? Use This Secret Viral PDF Rebrander: Viral PDF

In the employment world, the phrase ?manual labor? is often associated with jobs which are dirty, psychologically sickening, or worse, both. Small to medium-size manufacturing enterprises are moving towards using the CNC(Computer Numerical Control) in their major manufacturing processes because of its fame in accuracy, flexibility and automation. If you’re one of these entrepreneurs, don’t jump in the bandwagon just yet.

Acquiring a CNC machine is more than just buying additional equipment; it also has a social aspect in it. Here is the low down:

PEOPLE-WISE

First, you have to consider the people who are working in your shop. How many people will be displaced if you buy a CNC machine? Keep in mind that a CNC machine is multi-operational; so it’s possible that a couple of laborers will be erased from the production team. Experts say that the healthy ratio is at least one-sixth (1/6) of your whole labor force.

You will be saving time and effort, yes, and that is the best thing about having a CNC machine. However, you might be worrying about actually terminating people because, to put it bluntly, you won’t need them anymore. A CNC machine, just like any machine, will need an operator. Instructions used by a CNC machine for operational execution are composed of CNC ?words/codes? and is in the form of a ?sentence?.

Does one of your people ever have experience with a CNC machine before? Can s/he formulate CNC instructions? If the answer to both questions are ?yes?, then that’s absolutely good news. However, if you answered ?no? to at least one of the questions, then there are more things to evaluate.

Are your people capable of fast-learning? If it pains you to terminate them because they have been good employees in the past, train them on how to use the CNC machine and how to compose instructions for it. There are plenty of free training kits online.

It seems like new information is discovered about something every day. And the topic of CNC is no exception. Keep reading to get more fresh news about CNC.

COMPANY-WISE

There’s a corporate adage that goes: ?Innovate or die?. There’s a lot of truth in that. A purchase of any CNC machine symbolizes a company’s decision to innovate to increase productivity. However, there are a few things that you need to note.

Review your company’s history. How long should you innovate drastically in terms of production? CNC equipment is expensive. It is an investment. In the long run, you may be forced to buy new equipment more often. Consider CNC heavily if you feel that your company innovates faster than other companies in terms of the industry that you belong to. After all, you can easily alter designs and material when you have CNC powered operations.

In most companies, ?Innovation? is another word for ?saving?. It means saving time, effort and space. In using CNC machines, the first two factors are sure savings while the third is not. People doing the labor and CNC machines often occupy the same amount of space. Do not romanticize a ?clearing of clutter? effect when you buy a CNC machine. You will keep up, in terms of production; but CNC equipment also occupies a lot of space. So in that aspect, it’s pretty much the same thing.

Another thing that you have to be reminded of is the level of accuracy that your company needs to produce. Intricate patterns on metal/wood will DEMAND CNC accuracy. So any time that you feel your company is ready for such innovation and accuracy, consider employing CNC in your manufacturing.

At the end of the day, the last aspect that you need to evaluate is you, yourself. As the owner/head manager, you have to KNOW AND UNDERSTAND the CNC machine and the software well. This is the biggest battle that you have to face.

The equation to improvement is simple a really good machine plus a really good operator (you). Do not easily be blinded by the salesmen’s poetry.

Knowing enough about CNC to make solid, informed choices cuts down on the fear factor. If you apply what you’ve just learned about CNC, you should have nothing to worry about.